Public education for Canada and the United States

Not a government agency, clinic, laboratory, or company directory

Emergency. Carbon monoxide alarm, smell of gas, fire, or someone suddenly very ill: leave the building and call emergency services. Do not stay to read this page or run a test.

Do I need an indoor air test?

Often the useful first step is finding water, opening a window, or writing down when the problem happens. A test helps when you already have a clear question and the method matches that question.

This page is for a homeowner, a renter, a buyer, or a small building manager who is not an air specialist. It explains the decision. It does not tell you that your building is safe, and it does not replace a doctor.

If this might be an emergency

Leave first. A carbon monoxide alarm, the smell of gas or rotten eggs, a fire, heavy smoke, or someone who is confused, fainting, or suddenly very ill is an emergency. Go outside. Call emergency services. Do not look for a test kit.

Carbon monoxide is a gas from burning fuel that did not burn completely. You cannot see it or smell it. A home alarm is there so you do not have to decide from symptoms. Headache, dizziness, nausea, weakness, and confusion can have many causes. If they start suddenly in a building with fuel-burning equipment, treat that as a reason to leave, not as a reason to browse meters.

After everyone is safe, the next job is the equipment and its vent: furnace, boiler, water heater, fireplace, stove, or a car left running in a garage. That is an inspection by someone qualified for that equipment. A general “air quality package” is not that inspection.

The six honest answers

Every concern on this page ends in one of these. More than one can be true.

  1. Get emergency help now. Alarm, gas smell, fire, or a person who is suddenly very ill.
  2. Fix an obvious source first. A leak, a new carpet, a dirty filter, a closed room, or smoke from outside.
  3. Have the building inspected. Someone looks at moisture, fans, and fuel-burning equipment before any laboratory sample.
  4. Watch over time. A meter left in place for hours, days, or months, because one moment is not the pattern.
  5. Take a targeted sample. Air, dust, or a piece of material goes to a lab for one named question.
  6. Write it down and check again. The problem is occasional, the source is already fixed, or you need a record more than a new test.

In plain words. Buy the test that answers the question you can say out loud. “Is the basement damp because of a leak?” is a building question. “Why does my child cough?” is a medical question. An air test cannot answer the second one.

Musty smell, stains, or a damp room

Mold is a living growth that needs moisture. If you can see staining, bubbling paint, or a musty smell, you already have information. The U.S. Environmental Protection Agency says that when mold growth is visible, sampling is usually unnecessary. There is no U.S. federal number that says a home “passes” or “fails” a mold test.

In plain words. The color of the growth does not tell you how dangerous it is. “Black mold” is a description, not a diagnosis. Any mold that is growing indoors means the materials got wet and stayed wet. The useful work is to stop the water and deal with the wet material.

Try this first

  1. Find the water. Look for a plumbing leak, a roof stain, window condensation, a wet basement, or a dryer that vents into the room.
  2. Stop the water, then dry the area. Public guidance says wet materials should be dried within about 24 to 48 hours if you want to limit new growth.
  3. Photograph the stain, and write the date. A photo is often a better record than a spore count.
  4. Small patches on a hard surface can often be cleaned by the household if nobody in the home is at high risk and the water was clean, not sewage. The U.S. EPA’s consumer guide uses about 10 square feet — roughly a 3-by-3-foot patch — as the size many people can handle themselves. That size is not a safety guarantee.
  5. Soft materials that stayed wet, such as ceiling tiles, carpet cushion, or drywall that is falling apart, usually need to be removed. Paint over mold does not remove the moisture.
  6. If the area is large, the water was sewage or floodwater, the heating system is involved, or someone in the home is very young, pregnant, older, has asthma, or has a weak immune system, get help instead of scraping it yourself.

When a test is worth it

A moisture inspection is worth it when you cannot find the water, when the smell continues after drying, or when a buyer, insurer, or property manager needs a written record of what was seen. Air or surface samples are worth it only for a specific follow-up question, such as whether a cleaned surface still shows growth, or whether a hidden space needs to be opened. They are a weak way to decide “is the house safe?”

What this cannot prove. A mold sample cannot prove the home is mold-free. It cannot prove that mold caused someone’s symptoms. Spore counts change with the weather, with vacuuming, and with the outdoor air that day. Two samples taken an hour apart can disagree.

A chemical smell, or a smell from something new

New paint, cleaner, flooring, cabinets, and furniture release gases while they cure. Those gases are often grouped under the name VOC, which means volatile organic compound: a chemical that can evaporate into the air. A smell means something is in the air. It does not name the chemical, and it does not measure how much.

Try this first

  1. Find what is new. Write the product and the day it arrived or was applied.
  2. Bring in outdoor air. Run the kitchen or bath fan if it blows outdoors. Keep the room from becoming a closed box.
  3. Give recent work time to air out before someone sleeps in that room, especially a baby or a person with asthma.
  4. Store paint, fuel, and strong cleaners outside the living space, in a place the product label allows.
  5. If the smell is gas or rotten eggs, leave and call the gas utility or emergency services. That is not a VOC project.

When a test is worth it

A laboratory sample is worth considering when a strong odour continues for weeks after airing out, and you can point to a product or an area. Formaldehyde, one chemical from some pressed wood and glues, needs its own method. A handheld “VOC meter” that shows one total score is not a list of chemicals and is not a formaldehyde test.

What this cannot prove. No home test lists every chemical in the room or proves a health effect. A low score on a consumer meter does not mean the air is safe. A high score does not name the source.

Dusty air or dusty surfaces

Dust is a mixture. It can include skin flakes, fabric fibers, soil, pollen, pet dander, smoke, and bits of building material. The smallest particles, called PM2.5, are smaller than 2.5 micrometers. They stay in the air longer and can be breathed deep into the lungs. A thick layer on a shelf is mostly larger stuff that settled. Those are related, and they are not the same measurement.

Try this first

  1. Check the furnace or air-handler filter. Use the type the equipment maker allows, and replace it when it is loaded. A filter that is too restrictive can strain the equipment.
  2. Notice the pattern. Dust after pets, a renovation, cooking, candles, or an open window has a different meaning than dust that never stops.
  3. Vacuum and damp-wipe. Dry sweeping throws particles back into the air.
  4. Look at return grilles. A little gray dust is common. Wet dust, a musty smell, or debris piled inside the duct is a moisture or maintenance problem, not a reason to buy a particle count first.

When a test is worth it

Particle monitoring over hours or days is useful when dust continues after those steps, or when you need to see what happens during wildfire smoke or construction. One reading while someone is cooking will look worse than the same room an hour later. That spike is real, and it is not the all-day average.

What this cannot prove. A particle number does not name the dust. It does not prove the dust is harming a particular person. Outdoor air standards for cities are not a pass/fail law for a ten-minute reading in a kitchen.

Stuffy rooms, or headaches only in the building

A closed room fills with the air people breathe out, plus moisture from showers and cooking. Carbon dioxide, written CO2, rises when people are present and fresh air is limited. Outdoor air is a little above 400 parts per million. Indoor air is higher.

In plain words. Carbon dioxide and carbon monoxide are different gases. Home alarms are for carbon monoxide (CO), the poisoning gas from combustion. A carbon dioxide reading does not tell you whether carbon monoxide is present.

Health Canada’s home guideline for carbon dioxide is 1,000 parts per million as a 24-hour average. The agency’s own technical notes say the complaints seen in studies may come from stuffy air in general, not from carbon dioxide acting as a poison by itself. ASHRAE, the building-ventilation standards body, does not set 1,000 ppm as a pass/fail limit in Standard 62.1. Older explanations are often misquoted that way. A workplace limit near 5,000 ppm is for workers on a shift. It is not a target for a bedroom.

Try this first

  1. Open a path for outdoor air, when outdoor air is safe to bring in.
  2. Use bath and kitchen fans that exhaust outdoors. A fan that blows into the attic does not finish the job.
  3. Notice whether the discomfort happens when many people share a closed room, and whether it eases when they leave.
  4. Check that supply and return vents are not blocked by furniture.

When a test is worth it

A carbon dioxide logger left in the room during normal use shows whether fresh air keeps up with the people. Pair it with temperature and humidity. Use it as a ventilation clue. If headaches are severe, sudden, or come with an alarm, leave. That pattern belongs in the emergency section, not in a carbon dioxide log.

What this cannot prove. A carbon dioxide number does not diagnose a headache. A single reading of 1,200 ppm at a crowded dinner is not a 24-hour average, so it is not a direct comparison with the Health Canada guideline.

Wildfire smoke or outdoor pollution indoors

Smoke is mostly fine particles. The useful work is to keep outdoor air out while the smoke is heavy, and to clean the air in the room people actually use. A test does not remove smoke.

Try this first

  1. Close windows and doors while outdoor smoke is heavy.
  2. If the heating system can recirculate, use that mode so it is not pulling smoky air in. Follow the equipment instructions.
  3. Use a higher-efficiency filter if the system maker says the equipment can handle it. A portable cleaner with a true HEPA filter in the room you occupy is another option. This site does not name brands.
  4. Skip candles, frying, and extra dust while the outdoor air is poor. Those add particles you can control.
  5. When the outdoor air clears, air the house out.

When a test is worth it

A particle monitor during the smoke, and again after it clears, shows whether the room stayed high. That record can matter for a school, an office, or a person who needs to show what happened. It still does not clean the air.

What this cannot prove. A low reading after the smoke passes does not rewrite what the room was like during the smoke. A high reading does not, by itself, tell a doctor what care a person needs.

Renovation, new flooring, or new furniture

Dust from cutting and sanding, plus gases from glues, paints, and new materials, often travel together. The first days are the worst. The right first step is control of the work, not a certificate that the renovation is “healthy.”

Try this first

  1. Ask the contractor to seal the work area and to vent dust outdoors or capture it, rather than letting it drift through the house.
  2. Air the space during and after the work. Wait before a baby or a person with asthma sleeps in a freshly finished room.
  3. Write down what was installed and when: flooring, cabinets, paint, insulation.
  4. If the building is old enough that lead paint or asbestos materials are possible, do not sand or drill them “to check.” Those materials need their own rules before they are disturbed. See the section below.

When a test is worth it

A targeted formaldehyde or other named-chemical sample is reasonable when odour or irritation continues well after airing out, and the product is known. Particle checks during dusty work show exposure while the work is happening. A single sample the next morning does not describe the day of sanding.

What this cannot prove. No test certifies a renovation as healthy. “Not detected” means the method did not see that chemical above its limit on that day. It does not mean the room contains nothing.

Radon

Radon is a radioactive gas from soil and rock. It can seep into the lowest level of a building. You cannot see it or smell it, so a test is the right tool. This is one of the few indoor concerns where testing really is step one.

Radon increases the risk of lung cancer. The risk is higher for people who smoke. Public health agencies say there is no known level that is completely free of risk. A result under the guideline is lower risk, not zero risk.

Canada and the United States do not use the same number. Health Canada’s guideline is 200 becquerels per cubic metre (Bq/m³). If the long-term average in a normally occupied area is above that, Health Canada recommends fixing the building within a year, sooner if the number is much higher, and getting it as low as practical. The U.S. EPA recommends fixing a home at 4 picocuries per litre (pCi/L) or higher, which is about 150 Bq/m³. The EPA also says to consider fixing between 2 and 4 pCi/L. Four pCi/L is not the same line as 200 Bq/m³. Use the guideline for the country where the building sits.

Where to get the test

Ask your local office before you buy a device. Some public-health units, towns, and libraries lend or give a long-term radon test. Some state programs sell one at low cost. Not every place does this, and a free batch can run out. This site does not keep a city list, because those offers change.

  • In Canada, call your local public-health unit and ask if they have a long-term radon test. Health Canada explains how the test works and how to read the result.
  • In the United States, start with your state radon office on the U.S. EPA state contact list. Ask whether that office offers a free or low-cost test.

If no local program has a test, place a long-term test yourself, or hire a person certified for radon measurement. This site does not name kit brands or monitors.

How to test

  1. In Canada, Health Canada’s usual advice is a long-term test of at least three months, in the lowest level where someone spends more than about four hours a day. The heating season is a useful time because the house is closed.
  2. In the United States, the EPA and CDC recommend testing homes below the third floor. A short-term test can run from two days up to 90 days and is common during a sale. A long-term test, more than 90 days, is a better picture of the year-round average.
  3. A plug-in monitor shows how the number rises and falls from day to day. Use that after a long-term result, or to check that a repair worked. A few days on a monitor is still a short test. It does not replace the months-long test as your first result.
  4. Follow the device instructions. For a short test, that usually means closed windows, the device in the lived-in lower level, away from drafts and off the floor, and left alone for the full time. Tampering with a test during a sale can be illegal in some states.
  5. A weekend result is a screening result. When time allows, confirm it with a longer test before you treat one short number as the yearly average. If a short test is clearly high, do not ignore it while you wait months.
  6. The test does not lower radon. Reduction usually means a fan and piping system installed by someone certified for radon repair, then a retest.

What this cannot prove. A radon test does not measure mold, chemicals, or carbon monoxide. A result under the guideline does not mean the building is “safe” in every other way. A mold certificate does not replace a radon credential when you hire someone to fix radon.

Buying or selling a home

A sale has a deadline, so people buy packages. Write the actual question before you buy one. A radon rule, a musty basement, a past fire, and “we want a healthy-home certificate” are four different jobs.

Try this first

  1. Ask what the contract or the lender actually requires. Radon rules differ by province, state, and lender.
  2. Separate moisture history from air sampling. A stain and a sump pump are visible facts. A spore count does not replace looking at them.
  3. Treat a short radon test as a screening result. Know what you will do if it is high: a second test, a price discussion, or a mitigation agreement.
  4. Read any “mold-free” or “healthy home” certificate as a description of a few samples, not as a warranty.

What this cannot prove. No inspection during a sale can promise the house will stay dry, or that a future leak will not grow mold. Testing answers the question that was scoped, on the day it was scoped.

Gas appliances or a carbon monoxide worry

Furnaces, boilers, water heaters, fireplaces, gas stoves, generators, and cars in attached garages can put combustion gases indoors when venting fails or when the equipment is used in the wrong place. Never heat a home with a gas oven. Never run a generator indoors, in a garage, or near a window. Never idle a car in an attached garage.

Try this first

  1. Install a carbon monoxide alarm on each level, including outside sleeping areas. Follow the alarm maker’s height and replacement instructions. Many alarms need replacement after 5 to 10 years. The button test checks the electronics. It does not check whether carbon monoxide is in the room.
  2. If the alarm sounds, leave and call emergency services. Do not air the house out and go back to sleep.
  3. Have fuel-burning equipment and its vent inspected by someone qualified for that equipment, on the schedule the manufacturer and local rules expect.
  4. Use a kitchen hood that exhausts outdoors when you cook with gas. Cooking also makes nitrogen dioxide and particles. A hood that only recirculates does less for those gases.

Health Canada’s residential guidelines for carbon monoxide are 10 parts per million averaged over 24 hours, and 25 parts per million averaged over one hour. A home alarm is built to warn of more urgent levels. It can stay quiet below those urgent levels. A quiet alarm does not prove the day-long average meets the guideline. The United States does not use one single federal “home carbon monoxide” number in the same way. Workplace numbers, such as an 8-hour occupational limit, are not bedroom standards.

What this cannot prove. A consumer “air quality” meter is not a substitute for an alarm or for an appliance inspection. A low reading at 3 p.m. does not describe what the furnace did at 3 a.m.

Someone feels unwell and suspects the building

Symptoms need a clinician. This site cannot tell you why a person coughs, gets headaches, or has a rash. Timing still helps both the clinician and anyone who later looks at the building.

Try this first

  1. If the person is suddenly confused, fainting, or very ill, leave and get emergency care.
  2. For other symptoms, contact a doctor, nurse practitioner, or clinic. Say where the symptoms happen and whether they ease away from the building.
  3. Write a simple log: place, time, what the room was doing (cooking, shower, closed windows, new paint), and who else was there.
  4. Look for a building condition you can act on: visible moisture, no fresh air, a fuel-burning appliance, smoke, or a strong new product.

When a test is worth it

Test the building condition, not the person. A moisture inspection, a ventilation log, or a radon test can answer a building question. A panel of twenty laboratory tests ordered “to explain the symptoms” usually does not. The results still need a doctor if the question is health.

What this cannot prove. An air sample does not diagnose asthma, allergy, infection, or poisoning. A normal-looking report does not prove the symptoms are unrelated to the building. It proves only what that method measured, where and when it was used.

Asbestos, lead, or one named chemical

These are not included in a general mold or “VOC” package. Each has a method of its own.

Asbestos. Some older insulation, floor tile, ceiling texture, and pipe wrap can contain asbestos. If the material is intact and will not be disturbed, the usual advice is to leave it alone. Testing matters when a renovation will cut, sand, or remove it. Do not break a piece off to see. A mold air test does not detect asbestos.

Lead. In the United States, lead paint is a known concern in housing built before 1978. The usual check for lead dust is a dust wipe, not a room air test. Sanding old paint spreads lead dust. Rules for renovation differ by country and state. This page is not legal advice.

One chemical. If a report, a product recall, or a spill names one chemical, ask for the method made for that chemical. A broad screen can miss it or report it in a way you cannot compare with a guideline.

What this cannot prove. One indoor-air package does not clear a house of asbestos, lead, and chemicals at the same time.

Renters, schools, and workplaces

If you rent, you can still leave for an emergency. For other problems, write to the landlord or property manager with dates and photos. Keep a copy. Landlord duties differ by province and state. This page cannot tell you the rule where you live.

A school, daycare, or workplace is not a do-it-yourself project. Tell the person responsible for the building, and ask what they will inspect. Staff health questions in a workplace may belong with occupational health, a union, or a public-health office, depending on the country and the job. A home test kit does not replace that process.

What to write down before you call anyone

A good investigator starts from this list. You can gather it without a meter.

  1. The question in one sentence. Example: “The basement smells musty after rain, and I can see staining on the north wall.”
  2. When it started, and when it is worse.
  3. Which rooms, and whether anyone sleeps there.
  4. Recent water, painting, new furniture, wildfire smoke, or a new furnace.
  5. Photos with dates.
  6. Whether anyone has had urgent symptoms. If yes, say that medical care is already happening or that you need emergency care. Do not send health details to a testing company as if the company were a clinic.

Take that sentence to the hiring guide and ask the company to say, in writing, whether their method can answer it.

Questions people ask

Can I get a radon test for free?

Sometimes. Call your public-health unit in Canada, or your state radon office in the United States, and ask. Some towns and libraries offer a long-term test while supplies last. If they do not, place a long-term test yourself. A plug-in monitor is a different tool, and you do not need one for the first test.

Should I test for mold if I can see it?

Usually no. If you can see or smell growth, the next step is the moisture, then cleaning or removing the damaged material. Testing does not tell you the species is “the dangerous one,” and there is no federal pass/fail number for spores in a house.

Is a hardware-store air meter enough?

A humidity meter is genuinely useful. A carbon monoxide alarm is necessary safety equipment, and it is not a precision lab. A gadget that shows “VOC” or “air quality” as one score cannot name chemicals or prove the room is safe. Use it only as a rough clue, and do not make a medical decision from it.

We had a test and the number looks scary. What now?

Read which substance it is, the unit, the averaging time, and which guideline the report used. A short reading is not the same as a day-long or year-long average. Then open the page on what a test can show. If anyone is ill, talk to a clinician. This site cannot interpret your report as a diagnosis.

Does a low result mean the house is safe?

It means that method, in that place, at that time, did not find a high level of the thing it measured. It does not clear every other substance, and it does not predict next winter.

Reviewed November 2026 for Canada and the United States. Agencies change guidance. This page is education, not an emergency service, a diagnosis, or legal advice.

Sources used for the public numbers and the “test or don’t test” advice:

Read this next